Product Code: MDC

Features: Water-based, Pure Acrylic Roof Paint, Ready to use, Self-priming, Heat reflective

The development of COOLROOF was based on our - over 2 decades successfully performing – PeraRoof. By using latest technologies and high performance raw materials, obvious improvements in a number of aspects have been achieved:

No bleeding or washing off during rainfalls
Colour retention, as only lightfast pigments are used (no chalking or fading)
Further increased cooling effect
Corrosion protection – self-priming (not in coastal areas)
Improved adhesion and over coating.

COOLROOF is a water-based – self priming – pure Acrylic roof paint, based on special ceramic fillers and pigments to reflect UV-light rays and to interrupt the conductive heat transfer to the substrate.

However, maximum heat reflection will be achieved by using white or pastel shades COOLROOF. The heat isolating properties of COOLROOF are proportional to the applied dry film thickness.

Product Code: MEZ

Features: Economically priced, excellent hiding power, matt finish

CEILING PAINT is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with a high hiding power. This product was especially developed for housing schemes, factories ect., where White colour high hiding is important.

Product Code: MET

Features: Natural Cementations look, Non-patchy even finish, Long lasting / permeable, Ultraviolet- and alkali resistance, User friendly

MEDIUM TEX is creating a natural cementatious finish on exterior and interior walls. To be applied with a lamb wool roller or block brush, depending on desired pattern.

Product Code: ME0

Features: Economically priced, Good hiding power, Cleanable, Matt Finish

PVA GRADE 3 is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with good durability. Improved formula for mixing in pastel and deep colours with better dry hiding.

Product Code: MEL

Features: Good hiding power, cleanable, lightfast

PVA GRADE 2 is high quality emulsion paint with good clean-ability, formulated for interior and exterior use on plaster and concrete substrates.

Product Code: MEK

Features: Good hiding power, Cleanable, Lightfast

PVA ALL IN ONE is good quality emulsion paint with good clean-ability, formulated for interior and exterior use on plaster and concrete substrates.

Product Code: MEAG

Features: Hard Wearing, Fully Cleanable, UV Resistent

PVA GRADE 1 is a superior quality, pure Acrylic emulsion paint with excellent clean ability for interior and exterior use, providing an exclusive and durable finish. Suitable for use on clean galvanized iron, suitable primed steel, plaster and concrete, as well as for cool-rooms, schools and kitchens ect.

Product Code: MXRP-2

Features: High Flexibility, Good adhesion, Quick sandable.

FLEX FILL 2 is a highly flexible compound for use as crack filler for interior and exterior masonry and metal surfaces.

Product Code: MXRP-1

Features: High Flexibility, Good adhesion, Quick sandable

FLEX FILL is a highly flexible compound for use as crack filler for interior and exterior masonry, wood and metal surfaces.

Product Code: MXF-2

Features: Univeral Filler for interior and exterior use.

POWDER FILL dries to a solid and tough product that can be sanded easily to a smooth surface. This filler does not absorb water or humidity. POWDER FILL is suitable for filling small cracks, holes and other defects. It is also possible to skim uneven surfaces to a smooth finish with POWDER FILL.

Product Code: MB-30

Features: Water-based sealer on porous substrates, consolidates existing PVA coating before repainting

SEALER is a water based, transparent sealer, for use on porous and generally poor substrates. It is also suitable for the consolidation of existing coatings before repainting.

Features: A solven based bonding liquid for use on gypsum and poor substrate

BONDING LIQUID is a solvent based, transparent sealer, for use on porous and generally poor substrates. It is also suitable for the consolidation of existing coatings before repainting.

Product Code: MCE-1

PLASTER PRIMER is a water based, alkali-resistant, white prime coat, for use on plaster or concrete.

Product Code: MCWP-1

Features: Non Toxic (does not contain lead or chromates), Withstands temperatures of up to 150° C without decomposing, Can be welded

METAL PRIMER is a water based primer with excellent water resistance and long-term protection against corrosion. Using extremely powerful anticorrosion pigments and corrosion – inhibitors together with a resin base of the latest generation in polymer – chemistry. METAL PRIMER shows very good adhesion to a variety of substrates including: Mild steel - Galvanised steel – Aluminium – Copper – Brass – PVC Plastic - glass

Product Code: MR

Features: Hard wearing, Texture coating, Extreme Durability

TEX GRADE 1 is a superior quality, multi-purpose, decorative textured coating, with a high marble content, for use on exterior and interior surfaces.

Product Code: MRC

Features: Hard wearing, Rough texture coating

TEX GRADE 2 is a multi-purpose, decorative textured coating, for use on ceilings and other low abrasion surfaces.

Please fill in our online quotation form, stating some information about your specific project requirements and your contact details. We will then provide you with a quote, quickly and conveniently via email.

Product Code: MRL

Features: Superior quality smooth plaster, Long Lasting, On request, available in preferred colours

PLAST FINE is a superior quality, smooth plaster for use on interior or exterior surfaces.

Product Code: MRR (MRRF-FINE, MRRM-Medium, MRRC-Coarse)

Features: Superior quality rubbing plaster, Long Lasting, On request, available in preferred colour.

PLAST SCRATCH is a superior quality, rubbing plaster for use on interior or exterior surfaces. Available in three grades: Fine (1,6mm), Medium (3,2mm) and Coarse (4,8mm).

Product Code: MRT

Features: Superior quality fine plaster, Long Lasting, On request, available in preferred colours

PLAST STRUCTURE is a superior quality, fine plaster for use on interior or exterior surfaces.

Product Code: MRY

Features: Superior quality aggregate plaster, Long Lasting.

PLAST PEBBLE is a superior quality aggregate plaster for use on interior or exterior surfaces.

Product Code: MB-5

Features: Anti-efflorescent and Water repellant additive for plaster.

CEMENT ADDITIVE is a cement additive free of halogens and other aggressive constituents. It is eminently suitable for the modification of building plaster.

As a concrete and plaster additive which blocks efflorescence properties and in the production of a modified mortar.
As additive in the production of concrete flooring

Product Code: MB-6

Features: Increases Cement Plaster Flexibility

PERA FIX is a cement additive free of halogens and other aggressive constituents. It is eminently suitable for the modification of building plaster.

As a concrete and plaster additive (improves elasticity, adhesion and ratio of transverse and compressive strength) and in the production of plastics a modified mortar.
As additive in the production of concrete flooring (improves levelling, adhesion and enhances the early and ultimate strength of the floor).

Product Code: MB-9

Features: UV-Stable, Water Resistant

CLEAR COAT is a water based clear coat especially developed for interior application on walls coated with PVA, floors composed of cement, natural stone, non-glazed absorbing tiles ect. Hardwearing, water and dirt rejective – easy to clean.

Product Code: MB-20

Features: Protects against efflorescence, Shows decrease in water absorption, Water vapour Permeable

Latest water based silicone technology. ANT SALT PRIMER is used for the anti-efflorescent and water -repellent treatment of masonary. It protects against efflorescence and shows a remarkable decrease in water absorption. It has very good long term durability on external walls and is permeable to water vapour.The product can be over-coated with Acrylic PVA’s or texture - plasters.

Product Code: MDRC

Features: UV Stable, Very good adhesion, Highly flexible.

REPAIR COMPOUND is a highly flexible compound for use as joint and crackfiller, to seal roof leak and for flashing.

Product Code: MXC-1

Features: Multi-purpose Metal Cleaner

METAL CLEANER is a water-based cleaner to remove the wax layer from galvanised iron, prior to coating with METAL PRIMER (MCWP-1) and / or COOLROOF (DC). It may also be used to remove grease or oil from metal. It does not contain Hydrochloric Acid.

Product Code: XRP-2

Features: High Flexibility, Good Adhesion, Quick sandable.

PERA MASTIX is a highly flexible compound for use as crack filler for interior and exterior masonry and metal surfaces.

Product Code: CE-1

PERA AQUAPRIME is a water based, alkali-resistant, white prime coat, for use on plaster or concrete.

Product Code: CWP-1

Features: Non-toxic (doesn't contain lead or chromates), withstands tempretures of up to 150° C without decomposing, can be welded.

PERA METAL PRIMER is a water based primer with excellent water resistance and long-term protection against corrosion. Using extremely powerful anticorrosion pigments and corrosion – inhibitors together with a resin base of the latest generation in polymer – chemistry, Pera Metal Primer shows very good adhesion to a variety of substrates including: Mild steel - Galvanised steel – Aluminium – Copper – Brass – PVC Plastic - glass

Product Code: EH

Features: Rustic Natural Look, Permeable, Long lasting, Flexible, Ultraviolet- and alkali resistance, Environmental & user friendly

PERA FINE TEX is a Pure Acrylic wall coating, with a mini texture. To be used direct on plaster

Product Code: ER

Features: Silicon resin PVA, Good colour retention, Matt mineral finish (micro texture), Clean brilliant colour development

Description, Properties and Uses:

Water-vapour permeability
Water repellency
Colour fading (for optimal exterior performance we offer lightfast pigments)
Chalking- and UV-resistance
Resistance to saponification

PERA MICRO TEX, offers the solution to all the above mentioned critical aspects. It is recommended for interior and exterior use on primed plaster-, concrete- and fibre cement substrates, offering a hardwearing and good cleanable exclusive finish with very high water-vapour permeability together with excellent water repellency and extreme durability.

Product Code: EAG

Features: Hard Wearing, Fully Cleanable, UV Resistant

PERA SILK PVA is a superior quality, pure Acrylic emulsion paint with excellent clean ability for interior and exterior use, providing an exclusive and durable finish. Suitable for use on clean galvanized iron, suitable primed steel, plaster and concrete, as well as for cool-rooms, schools and kitchens ect.

Product Code: EG

Features: Hard Wearing, Flexible, Fully Cleanable, UV Resistant

PERA GLOSS PVA is a glossy, pure Acrylic emulsion paint with excellent clean ability for interior and exterior use, providing an exclusive and durable finish. Use on suitable primed metal and wood.

Product Code: EL

Features: Good hiding power, Cleanable, Lightfast

PERA SHEEN PVA is high quality emulsion paint with good clean ability, formulated for interior and exterior use on plaster and concrete substrates. (Peralin Paints Grade 2 PVA)

Product Code: EO

Features: Economically priced, Good Hiding Power, Cleanable, Matt Finish

PERA MATT PVA is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with good durability. Improved formula for mixing in pastel and deep colours with better dry hiding.

Product Code: EZ

Features: Economically priced, Excellent Hiding Power, Matt Finish

Pera CEILING PAINT is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with a high hiding power. This product was especially developed for housing schemes, factories ect., where White colour high hiding is important.

Product Code: DC

Features: Water-based, pure acrylic roof paint. Ready to use. Self-priming. Heat Reflective.

Pera Coolroof is a water-based – self priming – pure Acrylic roof paint, based on special ceramic fillers and pigments to reflect UV-light rays and to interrupt the conductive heat transfer to the substrate. However, maximum heat reflection will be achieved by using white or pastel shades Pera Coolroof. The heat isolating properties of Pera Coolroof are proportional to the applied dry film thickness.

Description, Properties and Uses:

The development of PERA COOLROOF was based on our - over 2 decades successfully performing – PeraRoof. By using latest technologies and high performance raw materials, obvious improvements in a number of aspects have been achieved:

No bleeding or washing off during rainfalls
Colour retention, as only lightfast pigments are used (no chalking or fading)
Further increased cooling effect
Corrosion protection – self-priming (not in coastal areas)
Improved adhesion and over coating.

Product Code: DF

Features: Self-priming, Pure Acrylic, UV-Resistant

PERA ROOFFELTING PAINT is a high quality, flexible Acrylic PVA paint for exterior use on Roof Felting sheets and fibre cement. Pera Rooffelting Paint is a durable, flexible and weather resistant roof insulation, which was especially developed for the coastal environment.

Product Code: DRC

Features: UV Stable, Very Good Adhesion, Highly Flexible

PERA REPAIR COMPOUND is a highly flexible compound for use as joint and crackfiller, to seal roof leak and for flashing.

Product Code: B-30

Features: Water-based sealer on porous sustrares, Consolidates existing PVA coating before repainting

PERA SEAL is a water based, transparent sealer, for use on porous and generally poor substrates. It is also suitable for the consolidation of existing coatings before repainting.

Product Code: B-9111

PERA SANDCOAT is a water based binder to be added to clean, sieved sand for a natural sand –plaster finish.

Product Code: EDM

Features: Primer and Topcoat in one product for exterior and interior use. Non-Toxic does not contain lead or chromates.

PERA DIRECT TO METAL is a waterbased PRIMER-TOPCOAT with excellent water resistance and long-term protection against corrosion. Using special pigments and corrosion inhibitors together with a resin base of the latest generation in polymer chemistry, Pera Direct to Metal shows very good adhesion to a variety of substrates including: Mild steel - Galvanised steel –Stainless Steel- Aluminium – Copper – Brass – PVC Plastic - Glass

Product Code: FS

Features: Ready to use, Flexible

PERA FLOOR PAINT is a quality, high build floor coating for use on interior and exterior concrete floors, with exceptional abrasion resistance. It should not be used on floors, which come in contact with breakfluid, solvents, oils, ect.

Application by brush or roller
Easy application (PVA like).
Dries to a tough finish
Can be applied direct to plaster, concrete and fibre cement substrate (self-priming)

Product Code: FT

Features: Ready to use, Flexible

PERA TENNIS FLOOR is a superior quality, high build concrete coating, with coarse aggregate (for improved grip) for use as a tennis court dressing

Application by brush or roller
Easy application (PVA like).
Dries to a tough finish
Can be applied direct to plaster, concrete (self-priming)

Product Code: R

Features: Hard wearing, Texture Coating, Extreme Durability

PERA ROLL is a superior quality, multi-purpose, decorative textured coating, with a high marble content, for use on exterior and interior surfaces.

Product Code: RS

Features: Superior quality decorative fine texture coating, highly elastic, Covers hair cracks

PERA STIPPLE PAINT is a superior quality, Interior/Exterior, decorative textured wall coating, with fine particle size filler content. The coating is highly elastic and recommended for hair-crazed concrete substrates, as well as areas where high impact resistance is required (e.g.: staircases). This coating can be applied either as a one or two coat system.

TOWN / BRANCH	TELEPHONE NUMBER	EMAIL
Windhoek (Sales)	+264 61 227 050	marius@peralinpaints.com
Swakopmund (Sales)	+264 64 462 888	roger@peralinpaints.com
Ongwediva (Sales)	+264 65 232 035	elifas@peralinpaints.com
Windhoek (Factory)	+264 61 235 870 / 22 77 73	peralin@afol.com.na

Features: Easy to apply, Smooth finish. Quick sandable.

SKIM COAT White is a water-based skimming coat for masonry, concrete and ceiling board. It is used as a skim-coat to fill and repair cracks, smaller holes, surface blemishes or other surface imperfections.

We are offering premium quality paints ranging from PVA paints, texture coatings and plasters, roof coatings and special coatings from Namibian resources, which are ideal to withstand Namibia’s tough climate conditions.

Welcome to the paint expert.
Let our expert team share some great advice on proper paint application and effective remedies of damages and wear. We look at fixing peeling, flaking or fading paints, and provide some tips how work with different surfaces, and how to prepare such surfaces correctly.

Welcome to the paint expert.
Let our expert team share some great advice on proper paint application and effective remedies of damages and wear. We look at fixing peeling, flaking or fading paints, and provide some tips how to work with different surfaces, and how to prepare such surfaces correctly.

Peralin Paints donated 700 litres of paint at a total value of N$120,000 for a face-lift for Jan Mohr Secondary School, to make the institution more encouraging for the learners and enjoy the environment in which they are being taught. According to Mr. Gert Maasdorp, Chairman of the school board, the partnership between Peralin Paints and the school won’t be the last as further upgrading work is still to be done. Mr. Koppers, the principal of the school, emphasized that he had fantastic results using Peralin Paints for his own house, saying “it’s a good quality Namibian product and I urge the public to try Peralin Paints for best quality ever”. Peralin Paints received a Certificate of Appreciation from Jan Mohr Secondary School for the valuable community support.

Peralin Paints supported Women At Work with the look and feel of their new offices in Windhoek West, by sponsoring paints for the entire outside area including the building. Peralin Paints is proud to be associated with this non-profit training centre that has a special focus on the training and development of semi-skilled unemployed Namibian women who are willing to empower themselves through education.

Every year, Peralin Paints is committed to make our schools a joyful and uplifting experience, especially for younger children and their teachers, by donating paint for building renovations.

Some of the sponsorships throughout 2020:

Sponsorship of paint to Pikkiepark Pre-primary in Academia in Windhoek for building renovations
Sponsorship of paint to Suiderhof Pre-primary school to paint their wall and murials
Renovation of Toivo ya Toivo Pre-primary school at Havana.

test

test test test

Peralin Paints, in partnership with Kosmos 94.1, has embarked on a mission to support these families with basic critical items, such as foods and blankets.
The Havanna Settlement was identified as one of the communities with hundreds of families in critical need, which has been chosen as the first charity initiative. Similar families of other settlements will also be supported in the future.
Our long-term goal is to empower the younger generation and provide them with the opportunities for development and training, enabling them to earn an income, to become a productive part of the community, and to achieve a sustainable lifestyle.

MER - PERA MICRO TEX (PERA PERM)

PeraFix

Another Product Image

PeraFix

Another Product Image

PeraFix

Another Product Image

PeraFix

Another Product Image

MEH - PERA FINE TEX

MEZ - Ceiling Paint

MEO - PVA Grade 3

PeraFix

Another Product Image

PeraFix

Another Product Image

MEK - PVA ALL IN ONE

MEL - PVA Grade 2

MEAG - PVA Grade 1

MEDM - Pera Direct-To-Metal

MENG - PVA Gloss Non-Block

MB-911 Pera Sand Coat

MB-9 Clear Coat

MXC-1 Metal Cleaner

Another Product Image

MB-30 Sealer

MB-20 Anti Salt Primer

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2 to 3	-
Coverage	4 to 5	m² / Ltr
Surface Apperance	Matt, Mineral Look	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See Colour Card and White other pastel and deep colours on request	-
Unit Sizes and Weights	20Ltr =22kg, 5Ltr = 5.6kg, 1Ltr = 1.2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	+/- 7	m² / Ltr
Surface Apperance	Matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	White Only	-
Unit Sizes and Weights	20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	4	hours
Recommended number of coats	1 Prime Coat and 1 to 2 Topcoats	-
Coverage	5	m² / Ltr
Surface Apperance	Fine texture, cementatious matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See Colour card and white	-
Unit Sizes and Weights	20 Ltr = 32.9kg, 5 Ltr = 8.3kg, 1 Ltr = 1.7kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	+/- 7	m² / Ltr
Surface Apperance	Matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	20	Minutes
Drying Times - Hard Dry	2	Hours
Over coating Time	6	Hours
Recommended number of coats	2	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Slight Sheen	-
Cleaning Solvent	Water	-
Shelf Life	6	Months
Available Colours	Whilte, Other colours on request	-
Unit Sizes and Weights	20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Slight Sheen	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	20	Minutes
Drying Times - Hard Dry	2	Hours
Over coating Time	6	Hours
Recommended number of coats	2	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Sheen	-
Cleaning Solvent	Water	-
Shelf Life	6 Months	Months
Available Colours	Whilte, Other colours on request	-
Unit Sizes and Weights	20 Ltr = 25.7kg, 5 Ltr = 7kg, 1Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	Depends on thickness	minutes
Drying Times - Hard Dry	Depends on thickness	hours
Over coating Time	2 Depends on thickness	hours
Recommended number of coats	N/A	-
Coverage	N/A	m²/Ltr
Surface Appearance	Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6 Months	month
Available Colours	White	-
Unit sizes and weights	5Ltr = 5.5kg, 1Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	Depends on thickness	minutes
Drying Times - Hard Dry	Depends on thickness	hours
Over coating Time	2 Depends on thickness	hours
Recommended number of coats	N/A	-
Coverage	N/A	m²/Ltr
Surface Appearance	Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6 Months	month
Available Colours	White	-
Unit sizes and weights	5Ltr = 5.5kg, 1Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Combination of Mineral Compounds	-
Drying Times - Touch Dry	Depends on thickness	minutes
Drying Times - Hard Dry	Depends on thickness	hours
Over coating Time	1 Depending on thickness	hours
Surface Apperance	Matt White	-
Cleaning Solvent	Water	-
Shelf Life	6 Months	month
Available Colours	White	-
Unit Size and Weights	20kg, 10kg, 5kg, 2kg, 500g	bag

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	1 to 2 (depending on substrate)	-
Coverage	8 to 10	m² / Ltr
Surface Apperance	Transparent	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	N/A	-
Unit Sizes and Weights	20 Ltr = 21.3kg, 5 Ltr = 4.9kg, 1 Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Resin solution in solven	-
Flammability	Flammable	-
Drying Times - Touch Dry	3	hours
Drying Times - Hard Dry	6	hours
Over coating Time	12	hours
Recommended number of coats	1 to 2 (depending on substrate)	-
Coverage	8 to 10	m² / Ltr
Surface Apperance	Transparent	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr =21.1kg, 5Ltr = 4.8kg, 1Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	1	hours
Over coating Time	2	hours
Recommended number of coats	1 to 2 (depending on substrate)	-
Coverage	7	m² / Ltr
Surface Apperance	Matt, smooth	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte	-
Unit Sizes and Weights	0Ltr =28.6kg, 5Ltr = 7.3kg, 1Ltr = 1.5kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	2 to 3	hours
Recommended number of coats	2	-
Coverage	6 to 7	m² / Ltr
Surface Apperance	Smooth - Semi Gloss	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Red	-
Unit Sizes and Weights	5Ltr = 6.5kg, 1Ltr = 1.3kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Polymer	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	3	hours
Recommended number of coats	2	-
Coverage	1.4	m² / Ltr
Surface Apperance	Matt, Textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr =36kg, 5Ltr = 9.4kg, 1Ltr = 1.9kg	Ltr = kg

Data Product

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	3	hours
Recommended number of coats	2	-
Coverage	1.4	m² / Ltr
Surface Apperance	Matt, textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request *	-
Unit Sizes and Weights	20Ltr =37.5kg, 5Ltr = 9.5kg	Ltr = kg

* Other colours delivery time two work days, 100Ltr Mimimum order

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic polymer	-
Drying Times - Touch Dry	2	hours
Drying Times - Hard Dry	24	hours
Recommended number of coats	1	-
Coverage (1mm)	1.6 to 2	Kg / m²
Surface Apperance	Slight Sheen, textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Only on request*	-
Unit Sizes and Weights	20Ltr =32kg, 5Ltr =8,2kg	Ltr = kg

*Minimum order is 160kg or 5 x 20Ltr (32kg)

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	2	hours
Drying Times - Hard Dry	24	hours
Over coating Time	24	hours
Recommended number of coats	1	-
Coverage - Fine (1.6 mm)	3.5	Kg / m²
Coverage - Medium (3.2 mm)	4	Kg / m²
Coverage - Coarse (4.8 mm)	5.3	Kg / m²
Surface Apperance	Slight Sheen, textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr =32kg, 5Ltr =8kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	2	hours
Drying Times - Hard Dry	24	hours
Over coating Time	24	hours
Recommended number of coats	1	-
Coverage	3,5	Kg / m²
Surface Apperance	Slight Sheen, textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Only on request	-
Unit Sizes and Weights	20Ltr =32kg, 5Ltr =8,2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	2	hours
Drying Times - Hard Dry	24	hours
Over coating Time	24	hours
Recommended number of coats	1	-
Coverage - Pera Pebbleplast	3,5	Kg / m²
Coverage - Pebbles: 6.4 mm (1/4")	4,8	Kg / m²
Coverage - Pebbles: 4.8 mm (3/16")	5,4	Kg / m²
Coverage - Pebbles: 3.2 mm (1/8")	6	Kg / m²
Coverage - Pera Acrylic Clear coat	0.3	Kg / m²
Surface Apperance	Aggregate Plaster	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Only on request *	-
Unit Sizes and Weights	20Ltr =33kg, 5Ltr =8.2kg	Ltr = kg

* Minimum order is 160kg or 5 x 20Ltr. Washed pebbles only available in White Marble Crush - delivery time 2 to 3 weeks.

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Alkaline Stable	-
Cleaning Solvent	Water	-
Shelf Life	6	Months
Unit Sizes and Weights	20Ltr =21,1kg, 5Ltr = 5.5kg, 1Ltr = 1.2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Alkaline Stable	-
Cleaning Solvent	Water	-
Shelf Life	6	Months
Unit Sizes and Weights	20Ltr =24,3kg, 5Ltr = 6.3kg, 1Ltr = 1.3kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	5	hours
Recommended number of coats	2	-
Coverage	+/- 10	m² / Ltr
Surface Apperance	Glossy	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Transparent	-
Unit Sizes and Weights	20Ltr =21.2kg, 5Ltr = 5.3kg, 1Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Silicone	-
Viscosity (Krebs Stormer)	Water think	-
Drying Times - Touch Dry	10	minutes
Drying Times - Hard Dry	N/A	hours
Over coating Time	48	hours
Recommended number of coats	2 to 3 (depending on surface absorption)	-
Dry Film Thickness	N/A	-
Coverage	8 to 10 (depending on surface absorption)	m² / Ltr
Surface Apperance	N/A (Transparent)	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	N/A (Transparent)	-
Unit Sizes and Weights	20Ltr = 20,9kg, 5Ltr = 5,4kg, 1Ltr = 1,1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	Depends on film thickness	hours
Over coating Time	+/- 6 (Depends on Film Thickness)	hours
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card and White	-
Unit Sizes and Weights	5Ltr = 6.8kg, 1Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Appearance	Blue Liquid	-
Coverage	6	m²/Ltr
Cleaning Solvent	Water	-
Shelf Life	6	Months
Recommended number of Applications	1 to 2	-
Unit Sizes and Weights	5Ltr = 5.2kg, 1Ltr = 1.2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	Depends on thickness	minutes
Drying Times - Hard Dry	Depends on thickness	hours
Over coating Time	2 Depending on thickness	hours
Recommended number of coats	N/A	-
Coverage	N/A	m² / Ltr
Surface Apperance	Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte	-
Unit Sizes and Weights	5Ltr = 5.5kg, 1 Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	1	hours
Over coating Time	2	hours
Recommended number of coats	1 to 2 (Depending on thichkness)	-
Coverage	7	m² / Ltr
Surface Apperance	Matt, Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte	-
Unit Sizes and Weights	20Ltr =28.6kg, 5Ltr = 7.3kg, 1Ltr = 1.5kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	2 to 3	hours
Recommended number of coats	2	-
Coverage	6 to 7	m² / Ltr
Surface Apperance	Smooth (Semi-Gloss)	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Red	-
Unit Sizes and Weights	5Ltr = 6.5kg, 1Ltr = 1.3kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	4	hours
Recommended number of coats	1 Prime-Coat and 1 to 2 topcoats	-
Coverage	5 to 6	m² / Ltr
Surface Apperance	Fine Texture - Matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card, other colours on request	-
Unit Sizes and Weights	20Ltr = 30.1kg, 5Ltr = 7.6kg, 1Ltr = 1.5kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Silicone modified Acrylic Emulsion	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	1 prime-coat / 2 Top Coats	-
Coverage	6 to 7	m² / Ltr
Surface Apperance	Matt Mineral Finish	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card and White, Other Colours on Request	-
Unit Sizes and Weights	20Ltr = 28.2kg, 5Ltr = 7, 1 Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Sheen	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr =25,7kg, 5Ltr = 7kg, 1Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	8	m² / Ltr
Surface Apperance	Gloss	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request (Available in 3 base colours)	-
Unit Sizes and Weights	20Ltr =22,9kg, 5Ltr = 5,9kg, 1Ltr = 1.3kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Slight Sheen	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr = 32.6kg, 5Ltr = 7.7kg, 1Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	+/- 7	m² / Ltr
Surface Apperance	Matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request. This quality is only made in pastel and deep shaded	-
Unit Sizes and Weights	20Ltr = 32.6kg, 5Ltr = 7.7kg, 1Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2	-
Coverage	+/- 7	m² / Ltr
Surface Apperance	Matt	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Whilte, Other Colours available on request	-
Unit Sizes and Weights	20Ltr = 32.6kg, 5Ltr = 7.7kg, 1Ltr = 1.6kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	2 to 3	-
Coverage	4 to 5	m² / Ltr
Surface Apperance	Matt, Mineral Look	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card and White other pastel and deep colours on request	-
Unit Sizes and Weights	20Ltr =22kg, 5Ltr = 5.6kg, 1Ltr = 1.2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Pure Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	3	hours
Over coating Time	6	hours
Recommended number of coats	1 Prime Coat and 2 Top Coats	-
Coverage	4 to 5	m² / Ltr
Surface Apperance	Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card and White other pastel and deep colours on request	-
Unit Sizes and Weights	20Ltr =28.9kg, 5Ltr = 7.2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	Depends on film thickness	hours
Over coating Time	+/- 6 (depends on film thickness)	hours
Recommended number of coats	2 to 3	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card and White	-
Unit Sizes and Weights	5Ltr = 6.8kg, 1Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	1	hours
Over coating Time	6	hours
Recommended number of coats	1 to 3 (depending on substrate)	-
Coverage	8 to 10	m² / Ltr
Surface Apperance	Transparent	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	N/A	-
Unit Sizes and Weights	20Ltr =21.3kg, 5Ltr = 4.9kg, 1Ltr = 1.1kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	N/A	minutes
Drying Times - Hard Dry	N/A	hours
Over coating Time	N/A	hours
Recommended number of coats	Depends on application	-
Surface Apperance	Natural	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	N/A	-
Unit Sizes and Weights	20Ltr =21.2kg, 5Ltr = 5.3kg, 1Ltr = 1.1kg	Ltr = kg

Coverage: Differs from applicator to applicator and different sand compositions.

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	6	hours
Recommended number of coats	1 Prime Coat / 1 - 2 Top Coats	-
Coverage	7 to 8	m² / Ltr
Surface Apperance	Smooth, Semi-Gloss	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	White and Black	-
Unit Sizes and Weights	5Ltr = 6.6kg, 1 Ltr = 1.4kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	4	hours
Recommended number of coats	1 Prime Coat / 2 Top Coats	-
Coverage	+/- 5	m² / Ltr
Surface Apperance	Matt Finish	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card	-
Unit Sizes and Weights	20Ltr = 28.5kg, 5Ltr = 7,2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	4	hours
Recommended number of coats	1 Prime Coat / 2 Top Coats	-
Coverage	+/- 4	m² / Ltr
Surface Apperance	Matt finish	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	See colour card	-
Unit Sizes and Weights	20Ltr = 28.5kg, 5Ltr = 7,2kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	20	minutes
Drying Times - Hard Dry	2	hours
Over coating Time	3	hours
Recommended number of coats	2	-
Coverage	1.4	m² / Ltr
Surface Apperance	Matt, Textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	White, other Colours on Request	-
Unit Sizes and Weights	20Ltr =36kg, 5Ltr = 9.4kg, 1Ltr = 1.9kg	Ltr = kg

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic Copolymer	-
Drying Times - Touch Dry	30	minutes
Drying Times - Hard Dry	3	hours
Over coating Time	4	hours
Recommended number of coats	2	-
Coverage	3	m² / Ltr
Surface Apperance	Slight Sheen, Textured	-
Cleaning Solvent	Water	-
Shelf Life	6	months
Available Colours	Only on Request	-
Unit Sizes and Weights	20Ltr =28.1kg, 5Ltr =7kg	Ltr = kg

Contact Form

For more information about Peralin Paints or one of our products, kindly complete the form below.

Product Data

PROPERTIES	DATA	UNITS
Resin Type	Acrylic	-
Drying Times - Touch Dry	Depends on thickness (30 min)	minutes
Drying Times - Hard Dry	Depends on thickness (3 hours)	hours
Over coating Time	3 Depends on thickness	hours
Recommended number of coats	1	-
Film Thickness	3 to 4	mm
Coverage	N/A	m²/Ltr
Surface Appearance	Very Smooth	-
Cleaning Solvent	Water	-
Shelf Life	6 Months	month
Available Colours	White	-
Unit sizes and weights	5Ltr = 8.2kg, 1Ltr = 1.16kg	Ltr = kg

Peralin Paints offers three distinct product categories, based on the application requirement of our consumer segments: PeraBuild, PeraHome and PeraGreen.

Please feel free to give us feedback if our advice and instructions are helpful to you, or if you have encountered a specific issue that you would like to get some information on.

Product description

Water repellent, self- cleaning mini-texture PVA.

A durable self-priming acrylic PVA, characterised by its outstanding water repellency, water vapor permeability, self-cleaning and a hard-wearing finish. This product is suitable for exterior use on fibre cement, plaster and masonry substrates.

A water-based smooth skim coat.

High quality acrylic-based skim coat for skimming uneven plaster and repair of cracks, smaller holes, surface blemishes or other surface imperfections on concrete, masonry, fibre cement and ceiling board surfaces.

Product description

A universal, highly flexible crack filler with good adhesion and sand ability.

An exceptional high quality and low shrinkage acrylic crack filler for interior and exterior masonry and metal surfaces. After drying it can be sanded to a smooth surface.

I'm chaning description now

Product description

PeraFix (B6)

Concrete and plaster additive for the production of polymer–modified mortar (PMM) and polymer-modified concrete (PMC). PeraFix improves workability, increases flexural and compressive strength, adhesion, impermeability and durability properties of mortars and concrete. PeraFix is used for modification of hydraulic binders in applications including repair mortar, flooring, rendering, bonding, mineral sealing slurries and as cement based adhesive.

As building sand differs in grain size and contaminations (salts etc.) and there are different kinds of Portland Cement available, trials should be carried out before application, to familiarise yourself with the use of PeraFix, as well as determining the optimum quantities to be used. PeraFix should always be added to the water before the mixture is added to the cement sand/stone mix. PeraFix is not a "super-plasticiser" (for use in high-density concrete), although it has plasticising properties and a reduction in make-up water is usually possible. PeraFix is active in the mortar (better workability, flow, plasticising action, colour development, etc.), as well as in the cured concrete (higher transverse and compressive strength, improved elasticity and adhesion, as well as better colour development and colour retention in pigmented systems). PeraFix "cures" by the loss of water, therefore we recommend that PeraFix modified concrete be left to dry after hardening. PeraFix is not recommended for underwater use.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Galvanized Iron - New	PeraMetal Cleaner	N/A (Self Priming)
Mineral Substrate - Previously coated *	Prepare as below	Prepare as below

Previously coated* surface in good condition
Sand down glossy surfaces. Touch up holes with METAL PRIMER (MCWP-1). Make sure surface is clean and dry.

Previously coated* surface in poor (paint peeling and extreme chalking) condition
Remove existing paint.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral or Fiber Cement Substrate - New	One coat Plater Primer (MCE-1)	N/A
Mineral or Fiber Cement Substrate - Previously coated *	Prepare as below	N/A
Celloted - New	N/A	N/A
Celloted - Previously coated **	Prepare as below	N/A

Previously coated*mineral surface or fiber cement

Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30).

Previously coated** Cellotex
Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	1 coat MB-20	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A

Previously coated* surface in good condition

Sand down glossy surfaces. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). Seal POWDER FILL (MXF-2) with SEALER (MB-30). Make sure surface is clean and dry.

Previously coated* surface in poor condition: Remove existing paint.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	Plaster Primer (MCE-1)	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A
Cellotex - New	One coat Sealer (MB-30)	N/A
Cellotext - Previous coated **	Prepare as below	N/A

Previously coated*mineral surface or fiber cement

Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30).

Previously coated** Cellotex

Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	Plaster Primer (MCE-1)	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A

Previously coated* surface

Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30).

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	Plaster Primer (MCE-1)	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A

Previously coated* surface

Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30).

Surface Preparation

SUBSTRATE	CLEANER	SEALER / FIRST COAT	PRIMER
Mineral Substrate - New	N/A	One coat Plaster Prime (MCE-1)	N/A
Mineral Substrate - Previously coated *	Prepare as below	Prepare as below	N/A
Galvanized Iron - New	Clean with Metal Cleaner (MXC-1)	N/A	Apply 1 coat Metal Primer (MCWP-1)
Galvanized Iron - Previously coated **	Prepare as below	N/A	Prepare as below
Steel - New	Clean with Metal Cleaner (MXC-1)	N/A	Apply 1 coat Metal Primer (MCWP-1)
Steel - Previously coated ***	Prepare as below	N/A	Prepare as below

Previously coated* mineral surface

Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2). Leave to dry.

Previously coated** galvanized iron

Poor condition: Remove existing paint completely, and continue as for new galvanized iron.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed.

Previously coated*** steel

Poor condition: Remove existing paint completely, and continue as for new steel.
Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch in bare areas with METAL PRIMER (MCWP-1).

Application Instructions

Cracks and small holes in plaster
Surface must be clean and dry. Remove any crumbling plaster. Apply FLEX FILL 2 into cracks with a skimming blade. Leave to dry and sand smooth. If necessary apply again. WOOD, METAL

Application Instructions

Cracks and small holes in plaster
Surface must be clean and dry. Remove any crumbling plaster. Apply FLEX FILL into cracks with a skimming blade. Leave to dry and sand smooth. If necessary apply again.

Application Instructions

Mix POWDER FILL with water to a lump-free stiff paste. Apply this paste with a skimming blade or scraper within 15-20 minutes after mixing. After drying (hardening) sand to a smooth surface and remove the dust. Apply SEALER (MB-30) over prepared POWDER FILL.

Surface Preparation

Crumbling plaster, stonework, roughcast and mineral plaster finishes: Clean surface with a wire brush, re-plaster where necessary.
Consolidation of old coatings: Remove all loose and flaking paint. Repair defects.

Safety Precautions

Crumbling plaster, stonework, roughcast and mineral plaster finishes: Clean surface with a wire brush, re-plaster where necessary.
Consolidation of old coatings: Remove all loose and flaking paint. Repair defects.

Surface Preparation and Application Instructions

New interior or exterior plaster or concrete walls: Make sure surface is clean and dry. Apply one coat PLASTER PRIMER. As topcoat apply a Peralin Paints PVA as specified on relevant datasheet.

For application surfaces, other than above, please contact our sales department.

Surface Preparation

Always make sure surface is clean and dry before any sealer or primer is applied.

SUBSTRATE	PRIMER
Galvanized Ferrous Metal - New	Clean with PeraMetal Cleaner
Galvanized Ferrous Metal - Previously coated	See below
Non-Ferrous Metal - New	Clean with PeraMetal Cleaner
Non-Ferrous Metal - Previously coated	See below

Previously coated - paint in good condition: Sand down glossy surfaces. Touch up with METAL PRIMER. Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	BONDING LIQUID
Mineral Substrate - New	One coat SEALER (MB-30)	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A
Lime washed surfaces	N/A	One coat Bonding Liquid (MB-100)
Roughcast and textured mineral plaster finishes	Prepare as below	Prepare as below

Previously coated* mineral surface

Poor condition:
Remove existing paint completely, and continue as for new mineral substrate. Good condition - Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish. Make good any holes and cracks with FLEX FILL (MXRP-2). Leave to dry.
Lime washed surfaces:
Remove limewash with a steel brush. Seal surface with BONDING LIQUID (B-100) (preferably 2 coats). Leave to dry for 24 hours.
Roughcast and textured mineral plaster finishes
Clean walls and apply 1 coat SEALER (MB-30). Leave to dry for 3 hours.

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	One coat SEALER (MB-30)	N/A
Mineral Substrate - Previously coated *	Prepare as below	N/A
Lime washed surfaces	N/A	Prepare as below
Roughcast and textured mineral plaster finishes	Prepare as below	Prepare as below
Cellotex and hardboard - New	One coat SEALER (B-30)	N/A
Fiber Cement - New	One coat SEALER (B-30)	N/A

Previously coated* mineral surface

Poor condition
Remove existing paint completely, and continue as for new mineral substrate.
Good condition
Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish. Make good any holes and cracks with FLEX FILL (MXRP-2). Leave to dry.
Lime washed surfaces
Remove limewash with a steel brush. Seal surface with BONDING LIQUID (MB-100) (preferably 2 coats). Leave to dry for 24 hours.
Roughcast and textured mineral plaster finishes
Clean walls and apply 1 coat BONDING LIQUID (MB-100). Leave to dry for 24 hours.
Fiber cement - new
Clean surface and apply 1 coat SEALER (MB-30) Leave to dry for 24 hours.

Surface Preparation and Application Instructions:

New plastered walls and brickwork - Ensure surface is completely dry. Seal surfaces with SEALER (MB-30). Then proceed as follows: After two hours drying time, apply the PLAST FINE (MRL) with a stainless steel trowel and smooth down to the thickness of the largest pebbles (+/- 1mm).Level the plaster to an even and smooth surface with a clean stainless steel trowel (Do not use plastic or wooden trowels). Make sure that the trowel remains clean at all times.
Previously painted surfaces: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish (it is not recommended to apply PLAST FINE (MRL) over Enamel paints). Make good any holes and cracks with FLEX FILL (code MXRP) and continue as in (a).
Lime washed surfaces: Remove limewash with a steel brush. Seal surface with 2 (two) coats of solvent-based bonding liquid, leaving a drying time of at least 4 hours in-between coats. After 24 hours drying time continue as in (a).
Surfaces with microbiological problems (fungal or algae growth): Liberally apply an approved detergent and leave for 48 hours. Remove all loose matter and fungal or algae growth with a wire brush. Apply 1 coat anti-fungal SEALER (on request only), followed by anti-fungal PLAST FINE. Where a primer coat is used, this too should be anti-fungicidal. Microbiological problems are usually caused by faulty construction or design - find and remove the cause of the problem whenever possible.

Surface Preparation

New plastered walls and brickwork: Ensure surface is completely dry. Seal surfaces with SEALER (MB-30). Two different methods of application may be employed on the prepared substrate:
1. After two hours drying time, apply a primer coat (PVA GRADE 2 –MEL), colour matched to the PLAST SCRATCH). After a further 2 hours drying time apply the PLAST SCRATCH with a steel trowel and smooth down to the thickness of the pebbles. The plaster is then patterned by means of rubbing down with a plastic trowel, taking care that the trowel remains clean at all times. The pattern may be varied horizontally, vertically, circular, perpendicular or crossed.
2. The PLAST SCRATCH may also be applied directly to the prepared substrate, in which case care should be taken that the pebbles, penetrating onto the substrate, do not leave discolourations in the plaster. When this second method is employed, White PLAST SCRATCH may be used and subsequently over coated with a PVA GRADE 1 (MEAG) OR PVA GRADE 2 (MEL) of the required colour.
Previously painted surfaces: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish (it is not recommended to apply PLAST SCRATCH over Enamel paints). Make good any holes and cracks with Pera Mastix and continue as in (a).
Lime washed surfaces: Remove limewash with a steel brush. Seal surface with BONDING LIQUID (MB-100) (preferably 2 coats). After 24 hours drying time continue as in (a).
Roughcast and textured mineral plaster finishes: Sand down walls to a smooth, even finish, wash down, leave to dry and apply 1 coat BONDING LIQUID (MB-100). After 24 hours drying time continue as in (a).
Surfaces with microbiological problems (fungal or algae growth): Liberally apply an approved detergent and leave for 48 hours. Remove all loose matter and fungal or algae growth with a wire brush. Apply 1 coat anti-fungal Pera Seal, followed by anti-fungal PLAST SCRATCH. Where a primer coat is used, this too should be anti-fungicidal. Microbiological problems are usually caused by faulty construction or design - find and remove the cause of the problem whenever possible.

Surface Preparation

New plastered walls and brickwork: Ensure surface is completely dry. Seal surfaces with SEALER (MB-30). Two different methods of application may be employed on the prepared substrate:
1. After two hours drying time, apply a primer coat (PVA GRADE 2 –MEL), colour matched to the PLAST SCRATCH). After a further 2 hours drying time apply the PLAST SCRATCH with a steel trowel and smooth down to the thickness of the pebbles. The plaster is then patterned by means of rubbing down with a plastic trowel, taking care that the trowel remains clean at all times. The pattern may be varied horizontally, vertically, circular, perpendicular or crossed.
2. The PLAST SCRATCH may also be applied directly to the prepared substrate, in which case care should be taken that the pebbles, penetrating onto the substrate, do not leave discolourations in the plaster. When this second method is employed, White PLAST SCRATCH may be used and subsequently over coated with a PVA GRADE 1 (MEAG) OR PVA GRADE 2 (MEL) of the required colour.
Previously painted surfaces: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish (it is not recommended to apply PLAST SCRATCH over Enamel paints). Make good any holes and cracks with Pera Mastix and continue as in (a).
Lime washed surfaces: Remove limewash with a steel brush. Seal surface with BONDING LIQUID (MB-100) (preferably 2 coats). After 24 hours drying time continue as in (a).
Roughcast and textured mineral plaster finishes: Sand down walls to a smooth, even finish, wash down, leave to dry and apply 1 coat BONDING LIQUID (MB-100). After 24 hours drying time continue as in (a).
Surfaces with microbiological problems (fungal or algae growth): Liberally apply an approved detergent and leave for 48 hours. Remove all loose matter and fungal or algae growth with a wire brush. Apply 1 coat anti-fungal Pera Seal, followed by anti-fungal PLAST SCRATCH. Where a primer coat is used, this too should be anti-fungicidal. Microbiological problems are usually caused by faulty construction or design - find and remove the cause of the problem whenever possible.

Surface Preparation

New plastered walls and brickwork: Ensure surface is completely dry. Seal surfaces with SEALER (MB-30). Two different methods of application may be employed on the prepared substrate:
1. After two hours drying time, apply a primer coat (PVA GRADE 2 –MEL), colour matched to the PLAST SCRATCH). After a further 2 hours drying time apply the PLAST SCRATCH with a steel trowel and smooth down to the thickness of the pebbles. The plaster is then patterned by means of rubbing down with a plastic trowel, taking care that the trowel remains clean at all times. The pattern may be varied horizontally, vertically, circular, perpendicular or crossed.
2. The PLAST SCRATCH may also be applied directly to the prepared substrate, in which case care should be taken that the pebbles, penetrating onto the substrate, do not leave discolourations in the plaster. When this second method is employed, White PLAST SCRATCH may be used and subsequently over coated with a PVA GRADE 1 (MEAG) OR PVA GRADE 2 (MEL) of the required colour.
Previously painted surfaces: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish (it is not recommended to apply PLAST SCRATCH over Enamel paints). Make good any holes and cracks with Pera Mastix and continue as in (a).
Lime washed surfaces: Remove limewash with a steel brush. Seal surface with BONDING LIQUID (MB-100) (preferably 2 coats). After 24 hours drying time continue as in (a).
Roughcast and textured mineral plaster finishes: Sand down walls to a smooth, even finish, wash down, leave to dry and apply 1 coat BONDING LIQUID (MB-100). After 24 hours drying time continue as in (a).
Surfaces with microbiological problems (fungal or algae growth): Liberally apply an approved detergent and leave for 48 hours. Remove all loose matter and fungal or algae growth with a wire brush. Apply 1 coat anti-fungal Pera Seal, followed by anti-fungal PLAST SCRATCH. Where a primer coat is used, this too should be anti-fungicidal. Microbiological problems are usually caused by faulty construction or design - find and remove the cause of the problem whenever possible.

Application Instructions

Plaster mixture: Add 1Ltr of Cement Additive (MB-5) to 50kg of cement. The B-5 must be added to the water, before addition of sand and cement!

NB: For application surfaces, other than above, please contact our sales department.

Application Instructions

Consolidation of old crumbling cement floors:
1. Clean thoroughly.
2. Saturate floor with PeraFix: Water in a ratio of 1:4.
3. Avoid an excess of PeraFix:Water, as this can lead to the formation of a film, that becomes sticky under the influence of heat and can be peeled off.
Coating of freshly laid cement floors - to strengthen the surface and as protection against dirt:
1. Dilute PeraFix with water in a ratio of 1:4.
2. Apply to floor, as soon as it can be walked upon, by means of spraying, or with a rubber spreader.
3. This measure is particularly important if surfacing is ultimately to be carried out.
Reducing shrinkage and the danger of cracking in floating floors:
For this, 1 to 2% PeraFix, calculated on the cement content, is added to the mortar. If poor quality sand is used this amount should be increased to 10%. The PeraFix is best added to the make-up water or, if a mechanical mixer is used, directly to the mixer. It is advisable to apply a coating, as described in "2", to the floating floor.
Levelling compound for mastic asphalt:
For this purpose PeraFix is mixed with fine, washed sand or with river sand until a mixture, which can easily be trowelled, is produced. The ratio of PeraFix: Sand is about 1:3 by weight.
Levelling compound for concrete:
Portland Cement (type PZ 275) is mixed with fine river sand (max. particle size: 0,5 - 1 mm), in a ratio of 1:1,5 to 1:2 per weight. The coarser the grains, the more sand can be used. The mixture is moistened with PeraFix:Water in a ratio of 1:1. This mixture is applied to the cleaned substrate that has been saturated with a mixture of Perafix:Water in a ratio 1:4. The applied levelling compound must be kept moist for 1 to 2 days. The addition of fused alumina cement, to the Portland cement, accelerates hardening. We recommend the application of a mixture as described in "2".
Repair of damaged or uneven concrete flooring:
Unevenness in cement flooring and in concrete is, after thorough cleaning of the substrate, saturated with a mixture of PeraFix:Water in a ratio of 1:4. Before this coating has dried, a mortar, consisting of 3 parts by volume of sand (particle size 0 to 3 mm) and 1 part by volume ordinary Portland cement, compounded with a mixture of PeraFix:Water in a ratio of 1:4, is used to make good the damage. More severe defects can be prefilled with this mortar and a levelling compound, as described under 5, applied. This mortar can also be used for the preparation of actual flooring.
Increasing adhesion and elasticity, as well as reducing the tendency to crack, of terrazzo or single layer
hard concrete flooring: The substrate is pre-treated with a mixture of Perafix:Water in a ratio of 1:4. The mortar is prepared with the same mixture, instead of water. In the case of double-layer, hard concrete flooring, these recommendations apply only to the lower layer.
Base for bonding old and new concrete:
The old, thoroughly cleaned floor, is primed with a mixture of PeraFix:Water in a ratio of 1:4. A mixture, consisting of 1 to 2 parts by volume of sand, particle size 0 to 3 mm and, 1 part by volume of cement, mixed with PeraFix:Water in a ratio of 1:4, is brushed into the wet priming coat. Ordinary cement mortar (or concrete) is cast onto this base, while it is still wet.
Towelling compounds based on cement or casein for substrates:
These can be made to adhere more easily to the substrate if a mixture of PeraFix:Water, in a ratio of 1:4 to 1:8, is used instead of water for preparing the compound.
Smoothing, waterproofing compound for spraying, brushing or towelling:
A mixture of: 1 part by volume PeraFix 1 part by volume Ordinary white or grey Portland cement 2 parts by volume Water is thoroughly stirred and applied to the surface by means of a spray gun (2,5mm jet, 2.5 atg.), a brush or a smoothing trowel. By further dilution with water, a thinner coat can be applied. This mixture can also be used as a decor plaster, but the mixture may have to be adjusted by up to 1 part by volume clean fine sand (0 to 1mm). The cured coating may then be coated with any conventional builder’s paint.
Improved adhesion of renderings:
The bond strength of wall and ceiling renderings can be improved, and their elasticity increased, especially if
the surfaces are smooth, by the addition of 5% PeraFix, calculated on the make-up water
Increasing the tensile strength of synthetic/natural anhydrite flooring or plaster moulds:
The addition of 5% PeraFix, calculated on the binder increases the bending tensile strength of synthetic anhydrite flooring by approximately 50% (measured on 4 X 4 X 16 cm prisms after thorough drying). The same applies to natural anhydrite. Plaster moulds (e.g. models) can be made practically unbreakable and highly abrasion resistant by a correspondingly high addition of PeraFix, even if the structural components are thin. The desired amount must be determined by preliminary trials, depending on the stress and type of plaster used.
Grouting for all types of wall and floor tiles:
A dry mix consisting of: White cement 300 p.b.w. Pera marble dust 600 p.b.w. Rutile Titanium Dioxide 100 p.b.w. is made into a paste with a mixture of PeraFix:Water in a ratio of 1:9. The Titanium Dioxide may be replaced by any inorganic light fast pigment, or mixtures thereof, for coloured grouting. Care must be taken, that these pigments are compatible with cement.

NB: Remember - trials should be carried out before application, to familiarise yourself in the use of PeraFix, as well as determining the optimum quantities to be used. PeraFix is not a "super-plasticiser" (for use in high-density concrete), although it has plasticising properties and a reduction in make-up water is usually possible. PeraFix is active in the mortar (better workability, flow, plasticising action, colour development, etc), as well as in the cured concrete (higher transverse and compressive strength, improved elasticity and adhesion, as well as better colour development and colour retention in pigmented systems). PeraFix "cures" by the loss of water, therefore we recommend that PeraFix modified concrete be left to dry after hardening. PeraFix is not recommended for use underwater.

For application surfaces, other than above, please contact our sales department.

Surface Preparation

New cement, natural stone, non glazed absorbing tiles:
Clean surface of dirt, cement- and mortar droppings. Make sure surface is dry and clean.
Old cement, natural stone, non glazed absorbing tiles:
Clean surface thoroughly from all dirt, remove wax ect. Make sure surface is clean and dry.
Plastered walls coated with a PVA new
Make sure surface is clean and dry.

Surface Preparation

As a water repellent and anti-efflorescent barrier under film forming coatings on porous substrates:
Clean surface by means of scrubbing or steam / high-pressure water cleaning and allow substrate to flash off. Ensure that the substructure is free of oil and grease to ensure proper penetration of the ANTI SALT PRIMER. Repair crumbly or poor finishes as the ANTI SALT PRIMER has no binding.
As a water repellent barrier under film forming coating systems:
In order to prevent water penetration through hairline cracks and defects in impermeable exterior paint systems, ANTI SALT PRIMER can be used as a primer on the plaster, under such coatings. The substrate must be clean and dry and application should take place before painting of the topcoat.

Surface Preparation and Application Instructions

Joints and cracks:
Surface must be clean and dry. Break open large cracks and remove all loose plaster. Soak work area with SEALER (MB-30) and allow to dry. Add Marbel Dust Fine (MD200) +/- 10% to the REPAIR COMPOUND, to form a thick paste and apply 2 to 3 layers. Allow sufficient drying time between layers. Smooth surface while still wet, as it cannot be sanded when dry.
Sealing of roofs:
Remove loose screws and narrow hole by inserting matchsticks or wood shavings. Dip screw into REPAIR COMPOUND and fasten firmly. Holes and gaps can be sealed by flashing. Do not try to seal corroded roofs, as this would only be a temporary solution.
Flashing:
Make sure surface is clean and dry. For plastered surfaces seal with SEALER (MB-300. Apply a thin layer of REPAIR COMPOUND and cover with netting. Allow to dry and apply a second layer. Smooth surface while still wet, as it cannot be sanded when dry.

NB: REPAIR COMPOUND may not be used to repair cracks in swimming pools or any other area, where it will be covered by water. Tools must be cleaned with water immediately after use. SEALER (MB-30) and roof coatings see relevant datasheets. Remember a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department.

Application Instructions

New galvanised iron: Apply on substrate with a brush. Leave for 10 to 15 minutes. Wash with clean water, until all dirt and cleaner is removed. If necessary repeat procedure. Apply Coolroof (MDC) as soon as possible.
Old galvanised iron: Replace badly rusted sheets and remove millscale and rust. Proceed as above.

NB: The METAL CLEANER has to be washed of thoroughly with clean water. The clean substrate has to be over-coated as soon as possible. For application surfaces, other than above, please contact our sales department.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Surface Preparation and Application Instructions

New interior or exterior plaster or concrete walls:
Make sure surface is clean and dry. Apply one coat Pera Aquaprime. As topcoat apply a Peralin Paints PVA as specified on relevant datasheet.

NB: For application surfaces, other than above, please contact our sales department.

Surface Preparation

SUBSTRATE	PRIMER
Galvanized Ferrous Metal - New	Clean with Pera Metal Cleaner
Galvanized Ferrous Metal - Previously Coated	See below
Non-Ferrous Metal - New	Clean with Pera Metal Cleaner
Non-Ferrous Metal - Previously Coated	See below

Previously coated - paint in good condition:
Sand down glossy surfaces. Touch up with Pera Metal Primer Primer. Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	PRIMER	SEALER, UNDERCOAT
Mineral Substrate - New	1 Coat MB-20	N/A
Mineral Substrate - Previously Coated *	Prepare as below	N/A

Previously coated* surface in good condition:

Sand down glossy surfaces. Touch up holes and cracks with Flexfill (XRP-2) or PeraCrackfiller (MXF-2) (Seal Pera Crackfiller. with Pera Seal (B-30)). Make sure surface is clean and dry.

Previously coated* surface in poor condition: Remove existing paint.

Surface Preparation

SUBSTRATE	PRIMER / SEALER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	1 coat MB-20	N/A
Mineral Substrate - Previously coated *	n.a.	N/A

Previously coated – paint surface in good condition

Sand down glossy surfaces. Touch up holes and cracks with Flexfill (XRP-2) or PeraCrackfiller.(MXF-2) (PeraCrackfiller must be sealed with PeraSeal (B-30).) Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	CLEANER	SEALER / FIRST COATER	PRIMER
Mineral Substrate - New	One coat Pera Aquaprime	One coat Pera Aquaprime	N/A
Mineral Substrate - Previously Coated *	Prepare as below	Prepare as below	N/A
Galvanized Iron - New	Clean with Pera Metal Cleaner	N/A	Apply 1 coat Pera Antirust
Galvanized Iron - Previously Painted **	Prepare as below	N/A	Prepare as below
Steel - New	Clean with Pera Metal Cleaner	N/A	Prepare as below
Steel - Previously Painted ***	Prepare as below	N/A	Prepare as below

Previously coated* mineral surface :

Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix. Leave to dry.

Previously coated** galvanized iron:

Poor condition: Remove existing paint completely, and continue as for new galvanized iron.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed.

Previously coated*** steel:

Poor condition: Remove existing paint completely, and continue as for new steel.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch in bare areas with Pera Antirust.

Surface Preparation

SUBSTRATE	PRIMER
Wood - New	1 or 2 Coats Pera Seal
Wood - Previously Coated *	N/A
Galvanized Iron - New	Apply 1 coat Pera Metal Primer
Galvanized Iron - Previously Painted **	Prepare as below
Steel - New	Apply 1 coat Pera Metal Primer
Steel - Previously Painted ***	Prepare as below

Previously coated* wood :

Poor condition: Remove existing paint completely, and continue as for new wood.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix. Leave to dry.

Previously coated** galvanized iron:

Poor condition: Remove existing paint completely, and continue as for new galvanized iron.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed.

Previously coated*** steel:

Poor condition: Remove existing paint completely, and continue as for new steel.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch in bare areas with Pera metal primer.

Surface Preparation

SUBSTRATE	SEALER / FIRST COAT	UNDERCOAT, FIRST COAT
Mineral Substrate - New	One coat Pera Aquaprime	N/A
Mineral Substrate - Previously Coated *	Prepare as below	N/A

Previously coated* surface :

Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix (interior) or Pera Crackfiller (exterior). After drying seal Pera Crackfiller with Pera Seal.

Safety Precautions

SUBSTRATE	SEALER / FIRST COAT	UNDERCOAT / FIRST COATER
Mineral or Fiber Cement Substrate - New	One coat Pera Aquaprime	N/A
Mineral or Fiber Cement Substrate - Previously Coated *	Prepare as below	N/A
Cellotex - New	One coat Pera Seal	N/A
Cellotex - Previously Coated ***	Prepare as below	N/A

Previously coated*mineral surface or fiber cement :

Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate.
Good condition: Ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix (interior) or Pera Crackfiller (exterior). After drying seal Pera Crackfiller with Pera Seal.

Previously coated** Cellotex:
Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry.

Surface Preparation

SUBSTRATE	SEALER / FIRST COATER	UNDERCOAT / FIRST COATER
Mineral or Fiber Cement Substrate - New	One coat Pera Aquaprime	N/A
Mineral or Fiber Cement Substrate - Previously Coated *	Prepare as below	N/A
Cellotex - New	N/A	N/A
Cellotex - Previously Coated **	Prepare as below	N/A

Previously coated*mineral surface or fiber cement :

Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate.
Good condition - ensure surface is clean and dry, glossy surfaces have to be sanded down. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with Pera Mastix (interior) or Pera Crackfiller (exterior). After drying seal Pera Crackfiller with Pera Seal.

Previously coated** Cellotex:
Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry.

Surface Preparation

Always make sure surface is clean and dry before any sealer or primer is applied.

SUBSTRATE	CLEANER	PRIMER, SEALER
Galvanized Iron - New	Pera Metal Cleaner	N/A (Self-priming)
Mineral Substrate - Previously Coated *	Prepare as below	Prepare as below

Previously coated* surface in good condition:
Sand down glossy surfaces. Touch up holes with Pera Antirust primer. Make sure surface is clean and dry.

Previously coated* surface in poor (paint peeling and extreme chalking) condition: Remove existing paint.

Surface Preparation and Application Instructions

New Roof felting:
Remove loose particles with a brush. Rinse surface with clean water. Apply 1 coat Pera Rooffelting Paint 10% thinned with water. Leave to dry and apply two coats Pera Rooffelting Paint un-thinned. Use Pera Rooffelting Paint between overlapping sheets as glue.
Previously painted Roof felting:
Existing surface in poor condition - Replace roof felting sheets with new once and proceed as in (a). Existing surface in good condition – Wash surface with clean water, to remove dust, loose particles or salt. On the clean and dry surface apply 2 coats undiluted Pera Rooffelting Paint Paint.
New Fibre Cement:
Make sure surface is clean and dry. Proceed as in (a).
Previously painted fibre cement:
Existing surface in poor condition – remove existing paint completely. Make sure surface is clean and dry. Proceed as in (c.). Existing surface in good condition – total surface should be cleaned with clean water, to remove dust and loose particles or salt. On the prepared surface apply 2 coats undiluted Pera Rooffelting Paint.

NB: Always clean surface from loose particles, salt ect. For substrates not mentioned here, please contact our technical department. Remember – a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department.

Surface Preparation and Application Instructions

Joints and cracks:
Surface must be clean and dry. Break open large cracks and remove all loose plaster. Soak work area with Pera Seal and allow to dry. Add Pera Marbel Dust Fine (MD200) +/- 10% to the Pera Repair Compound, to form a thick paste and apply 2 to 3 layers. Allow sufficient drying time between layers. Smooth surface while still wet, as it cannot be sanded when dry.
Sealing of roofs:
Remove loose screws and narrow hole by inserting matchsticks or wood shavings. Dip screw into Pera Repair Compound and fasten firmly. Holes and gaps can be sealed by flashing. Do not try to seal corroded roofs, as this would only be a temporary solution.
Flashing:
Make sure surface is clean and dry. For plastered surfaces seal with Pera Seal. Apply a thin layer of Pera Repair Compound and cover with netting. Allow to dry and apply a second layer. Smooth surface while still wet, as it cannot be sanded when dry.

NB: Pera Repair Compound may not be used to repair cracks in swimming pools or any other area, where it will be covered by water. Tools must be cleaned with water immediately after use. For Pera Seal and roof coatings see relevant datasheets. Remember a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department.

Surface Preparation

Crumbling plaster, stonework, roughcast and mineral plaster finishes:
Clean surface with a wire brush, re-plaster where necessary.
Consolidation of old coatings:
Remove all loose and flaking paint. Repair defects.

Surface Preparation

NEW PLASTERED WALLS:

The plaster surface should first be sealed with Pera-Aqua Seal B-7 before the Sand-plaster is applied.
To obtain a cracked clay finish, the sand must have a very high percentage of Clay content which must be plastered onto the wall about 4mm thick.

PREVIOUSLY PAINTED WALLS:

Clean surface; Seal with Pera-Aqua Seal B-7 and then apply Sand-plaster with a brush

Surface Preparation

ALL SUBSTRATES MUST BE FREE OF: RUST, GREASE, OIL, DIRT AND DUST!

SUBSTRATE	PRIMER, SEALER
Galvanized Ferrous Metal - New	Clean with Pera Metal Cleaner
Galvanized Ferrous Metal - Previously Coated	See below
Non-Ferrous Metal - New	Clean with Pera Metal Cleaner
Non-Ferrous Metal - Previously Coated	See below

Previously coated - paint in good condition: Sand down glossy surfaces. Make sure surface is free of dust and dirt!

Surface Preparation

SUBSTRATE	PRIMER, SEALER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	Self Priming	N/A
Mineral Substrate - Previously Coated *	Prepare as below	N/A

Previously coated* surface painted with PVA, in good condition: Sand down glossy surfaces. Repair plaster where necessary. Make sure surface is clean and dry.
Previously coated* surface in poor condition: Remove existing paint.

Surface Preparation

SUBSTRATE	PRIMER, SEALER	UNDERCOAT, FIRST COATER
Mineral Substrate - New	Self Priming	N/A
Mineral Substrate - Previously Coated	Prepare as below	N/A

Surface Preparation

ALWAYS MAKE SURE SURFACE IS CLEAN AND DRY BEFORE ANY SEALER OR PRIMER IS APPLIED

SUBSTRATE	SEALER	BONDING LIQUID
Mineral Substrate - New	One coat Pera Seal	N/A
Mineral Substrate - Previously Coated *	Prepare as below	N/A
Lime washed Surface	N/A	One coat PeraBond
Roughcast and textured mineral platster finishes	Prepare as below	Prepare as below

Previously coated* mineral surface:
Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition - Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish. Make good any holes and cracks with Pera Mastix. Leave to dry.
Lime washed surfaces:
Remove limewash with a steel brush. Seal surface with PeraBond (preferably 2 coats). Leave to dry for 24 hours.
Roughcast and textured mineral plaster finishes: Clean walls and apply 1 coat PeraBond. Leave to dry for 24 hours.

ALWAYS MAKE SURE SURFACE IS CLEAN AND DRY BEFORE ANY SEALER OR PRIMER IS APPLIED

SUBSTRATE	SEALER	BONDING LIQUID
Mineral Substrate - New	One coat Pera Seal	N/A
Mineral Substrate - Previously Coated *	Prepare as below	N/A
Lime washed surfaces	N/A	1 to 2 Coats Pera Bond
Roughcast and textured Mineral Plaster finishes	Prepare as below	1 Coat Pera Bond

Previously coated* mineral surface:
Poor condition: Remove existing paint completely, and continue as for new mineral substrate.
Good condition: Remove all dust, dirt, grease and loose or flaking paint. Glossy paints must be sanded to a matt finish. Make good any holes and cracks with Pera Mastix. Leave to dry.
Lime washed surfaces:
Remove limewash with a steel brush. Seal surface with PeraBond (preferably 2 coats). Leave to dry for 24 hours.
Roughcast and textured mineral plaster finishes:
Clean walls and apply 1 coat PeraBond. Leave to dry for 24 hours.

Application Instructions

New surface

Cracks and small holes on masonry or concrete surface: Surface must be clean and dry. Remove any crumbling plaster. Apply SKIM COAT with a trowel or scraper into cracks. Leave to dry and sand smooth. (for a smooth surface, fine sandpaper +/- 140# should be used)
Ceiling board surface: Surface must be clean and dry. Apply SKIM COAT with a trowel or scraper. Leave to dry and sand smooth. (for a smooth surface, fine sandpaper +/- 140# should be used)

Previously coated* surface in good condition

Sand down glossy surfaces. Make sure surface is clean and dry. Proceed as for new surface.

Previously coated* surface in poor condition

Remove existing paint and proceed as above.

As topcoat apply two coats of Peralin Paints products such as:

PVA Grade 1 (MEAG) or PVA Grade 2 (MEL) or PVA Grade 3 (MEO) or PVA All In One (MEK) or Ceiling Paint (MEZ-1) or Medium Tex (MET) or Pera Fine Tex (EH) or Pera Micro Tex (ER)
directly onto dry surface.

NB: Skim Coat White is not a Primer or Undercoat. Use as supplied.

Our PeraHome range aims towards the private consumer, who seeks to renovate the home with a quality paint just like a pro – easy, clean, and effective. Our sales team will gladly assist in optimal colour matching, application advice and after-sales maintenance solutions.

Our PeraBuild range aims towards the professional builder and construction companies, seeking durable quality paints for any project. The choice of three different quality grading options will ensure builders meet their budget every time.

Peralin Paints offers three distinct product categories, based on the application requirement of our consumer segments: PeraBuild, PeraHome and PeraGreen.

Product Application

Mineral Substrate:

MASONRY: Prime with 1 coat Anti-Salt Primer MB-20.

GYPSUM boards, hardboard and unglazed brick: Prime with 1 coat Sealer MB-30

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

Product Application

A document can be added to the paragraph by completing the fields below. Once a document has been selected the document title field automatically becomes mandatory and should be used to describe to contents of the document.When copying text from a word document, kindly click on the Paste as plain text icon, and paste the text into the pop-up field. This will remove all formatting that is linked to a word document.

Product Application

Mineral Substrate:

MASONRY: Prime with 1 coat Anti-Salt Primer MB-20.

GYPSUM boards, hardboard and unglazed brick: Prime with 1 coat Sealer MB-30

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Mineral Substrate:

MASONRY:

• Prime with 1 coat Plaster Primer MCE-1.

• Touch up cracks and holes with Flex Fill MXRP-2 or Filler MXF-2.

• Seal MXF-2 with Sealer MB-30.

GYPSUM boards, plaster, hardboard and unglazed brick:

Prime with 1 coat Sealer MB-30.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up cracks/holes with Flex Fill MXRP-2 or Filler MXF-2.

• On prepared surface apply 1 coat Sealer MB-30.

PVC gutters and downpipes:

Sand surfaces and make sure it is clean and dry.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

Galvanised iron; mild steel:

• Clean to a water break free surface with Metal Cleaner MXC-1.

• Prime with 1 coat Metal Primer MCWP-1*.

Previous coated substrate in a firm condition:

• Remove poorly adhering or defective paint.

• Sand glossy surfaces and make sure surface is clean and dry.

• Touch up in bare areas with Metal Primer MCWP-1*.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

Mild steel, galvanised iron, aluminium sheeting

• Apply on substrate with a brush.

• Leave for 10 to 15 minutes.

• Clean surface with water to remove wax, dirt and the Metal Cleaner. If

necessary repeat procedure.

• After cleaning mild steel should be coated immediately.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

Concrete, ceiling board and fibre cement surface.

Remove all contaminations, and make sure surface is clean and dry.

Product Application

NB: FLEX FILL may be used to repair cracks in swimming pools or any other area where it will be covered by water. Tools must be cleaned with water immediately after use. For application surfaces, other than above, please contact our sales department.

Product Application

Floated floors (to reduce shrinkage and cracking):

On the thoroughly cleaned surface apply a mix of 1 part PeraFix with 4 parts water. Apply mixture to new floor surface, as soon as it can be walked on. Avoid an excess of the mixture, as this can lead to the formation of a film that can peel off. Immediately apply the following compound (apply before coating has dried). Add 1 to 2% PeraFix calculated on the cement content to the make-up water for the mortar. For poor quality sand contact our sales department as more PeraFix must be used.

Leveling compound for concrete:

On the clean surface apply a mixture of 1 part PeraFix with 4 parts water. Saturate the surface with the mixture and immediately apply the following compound (apply before coating has dried). Mix appropriate Portland Cement with fine sand (size 0,5 to 1mm). Mix PeraFix with water in the ratio 1:1 and prepare the cement /sand mixture with it. Apply this mixture to the prepared substrate. The leveling compound must be kept moist for 7 days.

Repair of damaged or uneven concrete flooring:

On the thoroughly cleaned surface apply a mixture of 1 part PeraFix with 4 parts water. Saturate the surface with the mixture and immediately apply the following compound (apply before coating has dried). Produce a mortar consisting of 3 parts by volume sand (particle size 1 to 3mm) and 1 part by volume appropriate Portland Cement. Mix PeraFix with water in the ratio 1:4 and prepare the cement /sand mixture with it. Apply this mixture to the prepared substrate. The leveling compound must be kept moist for 7 days.

Base for bonding old and new concrete:

The old, thoroughly cleaned floor, is primed with a mixture of PeraFix:Water in a ratio of 1:4. Mix sand and cement in a ratio of 1 to 2 parts by volume sand (particle size 1 to 3 mm) and 1 part by volume cement. Add appropriate PeraFix:Water in a ratio of 1:4. This mixture is brushed into the wet priming coat. Ordinary cement mortar (or concrete) is cast onto this base, while it is still wet.

Application Instructions

Apply 2 coats CEILING PAINT (EZ-1) with a sheepskin roller.

NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department.

Application Instructions

Apply with 2 coats MEDIUM TEX (MET) with a lamb wool roller and if desired, immediately drag with block brush for pattern.

PLASTER
Plaster must be dry and solid. Apply POWDER FILL. After drying of filler, sand to smooth surface. Apply SEALER (MB-30) over filler.

PRIMED PLASTER
It is preferred to fill up holes and blemishes once the walls are primed. This gives better visibility. POWDER FILL can be applied on PVA based wall-primers, but must be sealed with SEALER (MB-30).

EXISTING PAINTED SURFACES
POWDER FILL can be applied on existing PVA paint coating. For use on eggshell or high gloss enamels sand substrate well to a matt surface. Apply POWDER FILL. After drying of filler, sand to smooth surface. Apply SEALER (MB-30) over filler.

WOOD, FIBREBOARD OR SOFTBOARD
FLEX FILL (MXRP) is recommended for this application.

Application Instructions

New galvanized iron:
Apply 2 to 3 coats COOLROOF directly onto degreased and cleaned surface.

Previously coated mineral substrate
On previously coated, prepared surfaces, 2 coats of COOLROOF should be applied.

New fiber cement
Make sure fiber cement is free from dust & other contaminations by means of stiff brush – if necessary wash with clean water & let dry properly. Apply one coat COOLROOF thinned with 15% water, leave to dry and apply two coats un-thinned.

NB: Do not paint a roof in full sun (hot substrate) or very windy conditions. Make sure that the coating is dry, before it rains. Stir well before and during use. The optimal cooling properties of COOLROOF are only achieved with a white or pastel colour. For application surfaces, other than above, please contact our sales department.

Application Instructions

Crumbling plaster, stonework, roughcast and mineral plaster finishes: Apply one or two soaking coats of SEALER.
Consolidation of old coatings: Apply one soaking coat of Pera Seal 10% thinned with clean water.
New plaster Apply one soaking coat of SEALER, before painting with a PVA. .

Application Instructions

Crumbling plaster, stonework, roughcast and mineral plaster finishes: Apply one or two soaking coats of BONDING LIQUID.
Gypsum plasters : Apply one or two soaking coats of BONDING LIQUID.

NB: For application surfaces, other than above, please contact our sales department.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Application Instructions

Apply METAL PRIMER by spraying or brushing. Application by roller is not recommended.

For application surfaces, other than above, please contact our sales department.

Application Instructions

Apply 2 coats TEX GRADE 1 (R-) with a Foam roller. First coat may be diluted with 5 to 10% water - apply second coat undiluted.

NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. Clear coat (MB-9) is recommended for application over these systems for improved gloss, cleanability and decreased dirt retention. For application surfaces, other than above, please contact our sales department.

Apply 2 coats TEX GRADE 2 with a Foam roller. First coat may be diluted with 5 to 10% water - apply second coat undiluted.

NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. CLEAR COAT (MB-9) is recommended for application over these systems for improved gloss, clean-ability and decreased dirt retention. For application surfaces, other than above, please contact our sales department.

"DO'S" and "DON'TS" when using PLAST FINE (RL):

Never apply PLAST FINE in direct sunlight. Use a canvas or plastic sheet to shade areas where work is in progress. Whenever possible, apply on side of structure facing away from sun.
On very large areas apply PLAST FINE in panels (or fields). Allowance should be made for these panels during the design stage of a project. These panels would ideally encompass no more than the area that can be plastered by a single applicator in a shift. Wherever necessary, care must be taken that these panels are easily accessible from the scaffolding.
Where it is possible apply only one batch to a continuous panel or wall. Where this is impossible, ensure that the colour of all batches used, matches.
A single panel or wall should never be left uncompleted.
If more than one person is doing the application, care must be taken that the resultant pattern of any one person matches that of all the others.
When choosing persons to apply the plaster, take note that plasterers are better suited than painters.

NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. One coat CLEAR COAT (MB-9) is recommended for interior application over these systems in high traffic areas, to improve gloss and cleanability and to decrease dirt retention. For application surfaces, other than above, please contact our sales department or the technical department.

"Do's" and "Don'ts" when using Plast Scratch

Never apply PLAST SCRATCH in direct sunlight. Use a canvas or plastic sheet to shade areas where work is in progress. Whenever possible, apply on side of structure facing away from sun.
On very large areas apply PLAST SCRATCH in panels (or fields). Allowance should be made for these panels during the design stage of a project. These panels would ideally encompass no more than the area that can be plastered by a single applicator in a shift. Wherever necessary, care must be taken that these panels are easily accessible from the scaffolding.
Where it is possible apply only one batch to a continuous panel or wall. Where this is impossible, ensure that the colour of all batches used, matches.
A single panel or wall should never be left uncompleted. If work on a panel is interrupted for any reason, care must be taken that the working edge of the PLAST SCRATCH is kept moist, so that application can continue without a joint showing in this zone.
If more than one person is doing the application, care must be taken that the resultant pattern of any one person matches that of all the others.
When choosing persons to apply the plaster, take note that plasterers are better suited than painters. It is however advisable to include an experienced painter in the team, because PLAST SCRATCH manifests properties of both a paint, as well as a plaster.

"Do's" and "Don'ts" when using Plast Structure

Never apply PLAST SCRATCH in direct sunlight. Use a canvas or plastic sheet to shade areas where work is in progress. Whenever possible, apply on side of structure facing away from sun.
On very large areas apply PLAST SCRATCH in panels (or fields). Allowance should be made for these panels during the design stage of a project. These panels would ideally encompass no more than the area that can be plastered by a single applicator in a shift. Wherever necessary, care must be taken that these panels are easily accessible from the scaffolding.
Where it is possible apply only one batch to a continuous panel or wall. Where this is impossible, ensure that the colour of all batches used, matches.
A single panel or wall should never be left uncompleted. If work on a panel is interrupted for any reason, care must be taken that the working edge of the PLAST SCRATCH is kept moist, so that application can continue without a joint showing in this zone.
If more than one person is doing the application, care must be taken that the resultant pattern of any one person matches that of all the others.
When choosing persons to apply the plaster, take note that plasterers are better suited than painters. It is however advisable to include an experienced painter in the team, because PLAST SCRATCH manifests properties of both a paint, as well as a plaster.

"Do's" and "Don'ts" when using Plast Pebble

Never apply PLAST PEBBLE in direct sunlight. Use a canvas or plastic sheet to shade areas where work is in progress. Whenever possible, apply on side of structure facing away from sun.
On very large areas apply PLAST PEBBLES in panels (or fields). Allowance should be made for these panels during the design stage of a project. These panels would ideally encompass no more than the area that can be plastered by a single applicator in a shift. Wherever necessary, care must be taken that these panels are easily accessible from the scaffolding.
Where it is possible apply only one batch to a continuous panel or wall. Where this is impossible, ensure that the colour of all batches used, matches.
A single panel or wall should never be left uncompleted. If work on a panel is interrupted for any reason, care must be taken that the working edge of the PLAST PEBBLE is kept moist, so that application can continue without a joint showing in this zone.
If more than one person is doing the application, care must be taken that the resultant pattern of any one person matches that of all the others.
When choosing persons to apply the plaster, take note that plasterers are better suited than painters. It is however advisable to include an experienced painter in the team, because PLAST PEBBLE manifests properties of both a paint, as well as a plaster.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Application Instructions

New cement, natural stone, non-glazed absorbing tiles:
Apply two coats of Clear Coat leaving an over coating time of 5 hours. The finished surface must dry for at least 24 hours, before it is open for traffic.
Old cement, natural stone, non glazed absorbing tiles:
Proceed as in a.
Plastered walls coated with a PVA new
Apply one coat of Clear Coat.

Application Instructions

As a water repellent and anti-effloescent barrier under film forming coating systems
ANTI SALT PRIMER must be applied to the masonry as liberally as possible and very porous substrates must be coated twice, working wet in wet (apply the next coat, when substrate has absorbed the previous one and no longer shines). Remove excess product that is not absorbed. Tools such as brushes, rollers or spraying equipment are suitable for this purpose. Most synthetic paints (e.g.: Vinyl, Acrylic, Silicone) show good wetting and adhesion to substrates treated in this way, but preliminary trials are recommended, especially where cheaper types of paint are used. Do not thin the topcoat to be used. This type of pre-treatment of concrete substrates is recommended especially under coastal weather conditions, where water (and salt) damage is a common problem.

NB: Do not use ANT SALT PRIMER as a bonding liquid on substrates that are crumbly were the plaster has deteriorated, as the binding powers of this product are not sufficient to restore the plaster soundness to support subsequent coatings. Do not use on damp or wet surfaces. This product is not suitable for rendering gypsum water repellent. Do not use on previously coated surfaces.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

NB: Always use a sealer and / or primer, before applying Pera Ceiling Paint. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department.

Application Instructions

New galvanized iron:
Apply 2 to 3 coats Pera Coolroof directly onto degreased and cleaned surface.
Previously coated mineral substrate:
On previously coated, prepared surfaces, 2 coats of Pera Coolroof should be applied.
New fiber cement:
Make sure fiber cement is free from dust & other contaminations by means of stiff brush – if necessary wash with clean water & let dry properly. Apply one coat Pera Coolroof thinned with to 15% water, leave to dry and apply two coats un-thinned.

NB: Do not paint a roof in full sun (hot substrate) or very windy conditions. Make sure that the coating is dry, before it rains. Stir well before and during use. The optimal cooling properties of Pera Coolroof are only achieved with a white or pastel colour. For application surfaces, other than above, please contact our sales department.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Application Instructions

Crumbling plaster, stonework, roughcast and mineral plaster finishes:
Apply one or two soaking coats of Pera Seal.
Consolidation of old coatings:
Apply one soaking coat of Pera Seal 10% thinned with clean water.
New plaster
Apply one soaking coat of Pera Seal, before painting with a PVA.

.NB: For application surfaces, other than above, please contact our sales department.

Application Instructions

TROWEL APPLICATION:
The sand should be mixed with Pera Sand-Coat B-911 in the following ratio:
5 kg Sand : 1L Pera Sand-Coat B-911

BRUSH / ROLLER APPLICATION:
The most common mixing ratio for brush / roller application is:
6 Litre Sand : 2 Litre Water : 1,5 Litre Pera Sand-Coat B-911

Note: As sand composition differs from region to region, the mixing ratio might differ slightly. Therefore we recommend you doing your own trials on site prior to mixing larger quantities.

The “Sand – plaster” can be mixed in a clean concrete mixer. This plaster gets very hard and dries quickly and will stick to the concrete mixer. It is thus very important to clean it regularly with clean water to avoid the plaster sticking to the concrete mixer.

Application Instructions

Apply Pera Direct to Metal by spraying, rolling or brushing.

NB: For application surfaces, other than above, please contact our sales department.

Application Instructions

New mineral substrate:
For a long-term coating, apply 2 to 3 coats Pera Floor Paint directly onto mineral surface. First coat must be diluted with 10% water, consecutive coats to be applied undiluted.
Previously coated with PVA paint: On previously coated, prepared surfaces, 2 coats of Pera Foor Paint should be applied.

NB: Pera Floor Paint should not be applied on Epoxy Paints. For application surfaces, other than above, please contact our sales department.

Application Instructions

New mineral substrate:
For a long-term coating, apply 2 to 3 coats Pera Tennis Floor directly onto mineral surface. First coat must be diluted with 10% water, consecutive coats to be applied undiluted.
Previously coated with PVA paint:
On previously coated, prepared surfaces, 2 coats of Pera Tennis Foor should be applied.

NB: Pera Tennis Floor should not be applied on Epoxy Paints. DO NOT use Pera Tennis Floor on clay courts. Remember, a system is only as good as the substrate. Re-floor where substrate is in very bad conditions. For application surfaces, other than above, please contact our sales department.

Application Instructions

Apply 2 coats Pera Roll with a Foam roller. First coat may be diluted with 5 to 10% water - apply second coat undiluted.

NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. Pera Clearcoat (B-9) is recommended for application over these systems for improved gloss, cleanability and decreased dirt retention. For application surfaces, other than above, please contact our sales department.

Application Instructions

Apply 2 coats Pera Stipple Paint with a Sheepskin- or Foam roller.

NB: Remember - a system is only as good as the substrate. Replaster walls where the old plaster is crumbling or detached. Never use inferior sealers or primers. For application surfaces, other than above, please contact our sales department.

The brand new developed PeraGreen range is the smart choice for a “green” envornment-friendly and sustainable future, The application is low VOC, meaning our paints have reduced amounts of volatile organic compounds, producing less harmful chemicals.

Features

Very Strong
Water proof
Water Resistant
Select Quality

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Very Strong
Water proof
Water Resistant
Standard Quality

Features

Very Strong
Water proof
Water Resistant
Standard Quality

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant

Features

Very Strong
Water proof
Water Resistant
Standard Plus Quality

Features

Very Strong
Water proof
Water Resistant
Select Quality

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Very Strong
Water proof
Water Resistant
Premium Quality

Features

Wall primer
Water resistant
Acrilic based
Premium quality

Features

Wall primer
Water resistant
Acrilic based
Premium quality

Features

Wall primer
Water resistant
Acrilic based
Premium quality

Features

Wall primer
Water resistant
Acrilic based
Premium quality

Features

Wall primer
Water resistant
Acrilic based
Premium quality

Features

Skim coat

Water-based

Smooth

Premium quality

Features

Crack filler
Highly flexible
good adhesion
Premium quality

Features

Concrete and plaster additive
Cleaning solvent: Water
Unit size: 20lt, 5lt, 1lt
Quality Class: Premium

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water!
Ventilation	Ensure adequate ventilated application area!
Spillages	Soak up with sand or soil. Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	X
Goggles	-
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X

Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical advice!
Skin Contact	Immediately wash skin with soap and water!

Ventilation	Ensure adequate ventilated application area!
Spillages	Soak up with sand or soil. Prevent run off into drains or water ways.

Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Flammability	Not Flammable
Toxicity	N/A
Protective Clothing	Gloves

Keep out of reach of children. Do not allow fumes to become concentrated at work area. Do not ingest.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water!
Ventilation	Ensure adequate ventilated application area!
Spillages	Soak up with sand or soil. Prevent run off into drains or waterways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water!
Ventilation	Ensure adequate ventilated application area!
Spillages	Soak up with sand or soil. Prevent run off into drains or water ways!
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight.
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	X
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Safety Precautions

Gloves	X
Mask	-
Goggles	X
Swallowed	Rinse mouth with water. Give water to drink. Seek medical attention!
Eye Contact	Rinse eyes with water and seek medical attention!
Skin Contact	Immediately wash skin with soap and water.
Ventilation	Ensure adequate ventilated application area.
Spillages	Prevent runn off into drains or water ways.
Storage	Keep container tightly closed. Store in cool, dry place out of direct sunlight
Flammable	Not flammable.

Always keep product out of reach of children. Do not ingest. Avoid eye contact.

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Cleaning solvent	Water
Shelf-life	1 Year
Unit-size	20lt,5lt,1lt
Drying-time	2 hours
Finish	matt
Coverage	2 sqm
Coats	2

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1-2 hours
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: Pastel, deep, transparent
Coverage: 7-8m2/L

Product Datas

Drying time: 1 hour
Re-coating Time: 3 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white

Product Datas

Drying time: 1 hour
Re-coating Time: 3 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white

Product Datas

Drying time: 1 hour
Re-coating Time: 3 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white

Product Datas

Drying time: 1 hour
Re-coating Time: 3 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white

Product Datas

Drying time: 1 hour
Re-coating Time: 48 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white

Product Datas

Drying time: 1 hour
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white
Coverage on even surface (m2/l): 7

Product Datas

Drying time: 1 hour
Re-coating Time: 2 hours
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white
Coverage on even surface (m2/l): 7

Product Datas

Drying time: depends on thickness
Re-coating Time: depends on thickness
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white
Coverage on even surface (m2/l): n/a

Product Datas

Drying time: depends on thickness
Re-coating Time: depends on thickness
Cleaning solvent: water
Shelf-life: 1 year
Unit size: 20lt, 5lt, 1lt
Colour: white
Coverage on even surface (m2/l): n/a

Product Datas

Product Code: B6
Shelf-life: 1 year
Store paint in a dry cool place above 5ºC and protect from sunlight.

Our product quality and durability make Peralin Paints the first choice for major industrial projects, such as the Namibia Institute of Public Administration and Management building, the Meteorological Service building, United Nations building, Metropolitan Life, the Government Office Park and a significant number of schools, institutions and government buildings to mention only a few.

The 21st century has transformed Peralin Paints into a world-standard paints manufacturer with retail outlets in Windhoek, Swakopmund and Ongwediva.

With our endeavor to improve and develop superior products, we focus on paints that are one-system coatings, meaning that the paints do not require any primer or undercoat anymore, as those innovative products are self-priming. All products are also naturally water-based to guarantee an environmentally friendly application. In 2020, Peralin Paints joined the Green Building Counil of Namibia, showing our commitment to apply environment-friendly and sustainable green building methods.